Pioneer S-LX70W User Manual download pdf (Page 6)

• The installation location selected should have a sturdy

floor surface. Mounting the speaker on a long-pile

carpet should be avoided, since the carpet may touch

the driver’s diaphram, causing distorted sound.

• Please install this unit away from the antenna cable of

the tuner, as noise can be caused with installation

close to the antenna cable. In such a case, use this

unit at a position away from the antenna and the

antenna cable, or when playback of extra bass is not

required, switch off the power for this unit.

PANEL FACILITIES

FRONT PANEL

REAR PANEL

1 Power Indicator (STANDBY/ON)

Lights blue when the power has been switched ON.

When AUTO STANDBY switch is set to ON, lights blue

whenever the speaker receive an audio signal. If the

power is switched OFF only briefly, the indicator lights

blue when power is restored. If no signal is present for

more than 12 minutes, the subwoofer automatically

reverts to standby mode and the power indicator lights

red. If, subsequently, a signal is received, power

automatically comes back on and the power indicator

lights blue.

NOTE:

• If you are planning on switching the unit OFF for a long

period of time, make sure to check that the indicator

light has gone out after switching OFF.

2 Power switch (POWER)

When pressed, power is turned ON; when pressed

again, power is turned OFF.

3 Volume knob (VOLUME)

Sets the subwoofer volume.

• Turn the knob slowly from the MIN position.

• With this unit, the bass level can be independently

set, so do not turn up the bass on the AV amplifier.

4 Crossover knob (CROSSOVER)

When using the subwoofer, set the upper frequency

limit for the subwoofer (

50 Hz, 60 Hz, 70 Hz, 80 Hz,

100 Hz, 120 Hz, 160 Hz, 200 Hz

) so that it

complemets the output from your other speakers.

When using the bass managment features of an AV

receiver, set to

BYPASS ON

in order to use the low-

pass filter of the AV receiver for high quality sound.

5 Bypass switch (BYPASS)

When set to

, the audio signal is routed directly to

the woofer unit, bypassing the amplifier’s filter.

6 Bass mode switch (BASS MODE)

MUSIC

: The characteristic frequencies become flat.

Recommended for music sources.

CINEMA

: Low frequencies are emphasized.

Recommended for sources that require strong bass.

7 Phase switch (PHASE 0º /180º)

When set to

180º

, the output phase becomes the

reverse of the input signal, and when set to

0º

, it is in

the same phase as the input signal.

• Normally, the switch is set to

0º

But when the sound connection between the

subwoofer and the left and right speakers sounds

unnatural, try switching to

180º

and set the switch

in the position where the sound is natural.

• When using two or more subwoofers together,

make sure that the phase switch of all of them are

set to the same position.

MAINTENANCE OF EXTERNAL SURFACES

• Clean the surface by wiping with the provided

polishing cloth, or with another soft, dry cloth.

• When the surfaces are very dirty, wipe with a soft

cloth dipped in some neutral cleanser diluted five

or six times with water, and wrung out well, and

then wipe again with a dry cloth. Do not use

furniture wax or cleaners.

• Never use thinners, benzine, insecticide sprays

and other chemicals on or near this unit, since

these will corrode the surfaces.

POWER

STANDBY/ON

VOLUME

CROSSOVER

MAX

MIN

200Hz

160Hz

120Hz

100Hz80Hz

70Hz

60Hz

50Hz

BYPASS

OFF

BASS MODE

MUSIC

CINEMA

PHASE

180∞

0∞

AUTO STANDBY

OFF

LINE LEVEL

OUTPUT

INPUT

AC IN

9 11

S_LX70W_En.book 6 ページ２００７年７月１０日　火曜日　午後３時９分

1 2 3 4 5 6 7 8 9 10 11 ... 14 15

Comments to this Manuals

No comments

Pioneer S-LX70W User Manual Page 6

Comments to this Manuals

Related products and manuals for Audio amplifiers Pioneer S-LX70W