Pioneer VSX-1121-K User Manual download pdf (Page 21)

100

Connecting your equipment

Connecting AM/FM antennas

Connect the AM loop antenna and the FM wire

antenna as shown below. To improve reception

and sound quality, connect external antennas

(see Connecting external antennas on page 21 ).

ANTENNA

FM UNBAL 75 AM LOOP

a b c

1 Pull off the protective shields of both

AM antenna wires.

2 Push open the tabs, then insert one

wire fully into each terminal, then release

the tabs to secure the AM antenna wires.

3 Fix the AM loop antenna to the

attached stand.

To fix the stand to the antenna, bend in the

direction indicated by the arrow (fig. a) then clip

the loop onto the stand (fig. b).

! If you plan to mount the AM antenna to a

wall or other surface, secure the stand with

screws (fig. c) before clipping the loop to the

stand. Make sure the reception is clear.

4 Place the AM antenna on a flat

surface and in a direction giving the best

reception.

5 Connect the FM wire antenna into the

FM antenna socket.

For best results, extend the FM antenna fully

and fix to a wall or door frame. Don’t drape

loosely or leave coiled up.

Connecting external antennas

To improve FM reception, connect an external

FM antenna to FM UNBAL 75 W.

ANTENNA

FM UNBAL 75 AM LOOP

75 Ω coaxial cable

To improve AM reception, connect a 5 m to 6 m

(16 ft. to 20 ft.) length of vinyl-coated wire to the

AM LOOP terminals without disconnecting the

supplied AM loop antenna.

For the best possible reception, suspend hori-

zontally outdoors.

ANTENNA

FM UNBAL 75 AM LOOP

Outdoor antenna

Indoor antenna

(vinyl-coated wire)

5 m to 6 m

(16 ft. to 20 ft.)

MULTI-ZONE setup

This receiver can power up to two independent

systems in separate rooms after you have made

the proper MULTI-ZONE connections.

Different sources can be playing in two zones at

the same time or, depending on your needs, the

same source can also be used. The main and

sub zone have independent power (the main

zone power can be off while sub zone is on) and

the sub zone can be controlled by the remote or

front panel controls.

Making MULTI-ZONE connections

It is possible to make these connections if you

have a separate TV and speakers for the sub

zone (ZONE 2). You will also need a separate

amplifier if you are not using the MULTI-ZONE

setup using speaker terminals (ZONE 2) on page

21 for the sub zone.

MULTI-ZONE listening options

The following table shows the signals that can

be output to ZONE 2:

Sub

Zone

Input functions available

ZONE 2

DVD, TV/SAT, DVR/BDR, VIDEO,

HOME MEDIA GALLERY, iPod/USB,

CD, TUNER, ADAPTER PORT, SIRIUS

(Outputs analog audio, composite

video.)

It is not possible to down-convert the audio

and video input signals from the HDMI input

terminals, digital input terminals (OPTICAL and

COAXIAL) and the COMPONENT VIDEO input

terminals and output them to ZONE 2.

Basic MULTI-ZONE setup (ZONE 2)

1 Connect a separate amplifier to the

AUDIO ZONE 2 OUT jacks on this receiver.

You should have a pair of speakers attached to

the sub zone amplifier as shown in the follow-

ing illustration.

2 Connect a TV monitor to the VIDEO

ZONE 2 OUT jack on this receiver.

RS-232C

ZONE 2

IN IN

OUT

ZONE 3

OUT

TV/SAT VDVD

COMPONENT VIDEO

Y P

ASSIGNABLE

MONITOR

OUT

(

DVD

)

(

DVR/

BDR

)

BD IN

EXTENSION

SPEAKERS

FM UNBAL 75

AM LOOP

ANTENNA

(

OUTPUT 5 V

150 mA MAX

)

CONTROL IR

OUT

HDMI

(VIDEO)

ASSIGNABLE

1 6

R L

AUDIO IN

VIDEO IN

Sub zone (ZONE 2)

Main zone

MULTI-ZONE setup using speaker

terminals (ZONE 2)

You must select ZONE 2 in Speaker system set-

ting on page 66 to use this setup.

1 Connect a pair of speakers to the

surround back speaker terminals.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 99 100

Comments to this Manuals

No comments

Pioneer VSX-1121-K User Manual Page 21

Comments to this Manuals

Related products and manuals for AV receivers Pioneer VSX-1121-K