Pioneer DEH-X6600BT User Manual download pdf (Page 19)

Black plate (19,1)

Setting Parental Control

The SiriusXM Parental Control feature allows

you to control access to channels that you con-

sider inappropriate for younger listener.

When enabled, the Parental Control feature re-

quires you to enter a passcode to tune to the

locked channels.

Locked channels are indicated by a CH LOCKED

symbol.

1 Display PARENTAL CTRL.

2 Press M.C. to display the passcode input

screen.

The default passcode is 0000.

3 Turn M.C. to select a number.

4 Press M.C. to move the cursor to the next

position.

5 After inputting passcode, press M.C.

You will be able to proceed to the next step if you

enter the correct passcode.

6 Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

LOCKED CH (locking the channels)

Access to the current broadcast channel can be

locked. You will need to enter your passcode in

order to access a locked channel.

1 Press M.C. to select the desired setting.

2 Press M.C. to turn the lock on or off.

CLEAR ALL (clearing all channel locks)

You can clear the locks from all locked channels

at the same time.

1 Press M.C. to select the desired setting.

2 Turn M.C. to switch to YES.

3 Press M.C.

EDIT CODE (changing the passcode)

You can change your passcode.

1 Press M.C. to display the setting mode.

Enter your current passcode.

! The default passcode is 0000.

2 Turn M.C. to select a number.

3 Press M.C. to move the cursor to the next posi-

tion.

4 After inputting passcode, press M.C.

Enter a new passcode.

5 Turn M.C. to select a number.

6 Press M.C. to move the cursor to the next posi-

tion.

7 After inputting passcode, press M.C.

The new passcode is saved.

Resetting to default

The SiriusXM settings will be reset to the default

settings.

For details, refer to SXM RESET (SiriusXM Reset)

on page 17.

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do

not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire first.

Ensure that the ground wire is properly con-

nected to metal parts of the car’s body. The

ground wire of the power amp and the one of

this unit or any other device must be con-

nected to the car separately with different

screws. If the screw for the ground wire loos-

ens or falls out, it could result in fire, genera-

tion of smoke or malfunction.

Ground wire

Metal parts of car’s body

POWER AMP

Other devices

(Another electronic

device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may re-

sult in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

English

Available accessories

Section

Installation

<QRD3195-A>19

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 95 96

Comments to this Manuals

No comments

Pioneer DEH-X6600BT User Manual Page 19

Comments to this Manuals

Related products and manuals for Car media receivers Pioneer DEH-X6600BT