Pioneer HD1 Manual download pdf (Page 13)

Chapter 2 How to Use the Navigation System and Names of the Parts

When Using the Navigation Sys-

tem for the First Time

The navigation system cannot detect the location

correctly if the initial learning is not complete.

The correct positioning can be attained after driv-

ing a certain distance. (The AV source can be

used normally regardless of the initial learning

status.)

When the vehicle starts to run, the 3D Hybrid

Sensor’s initial learning automatically starts.

Until the 3D Hybrid Sensor’s initial learning is

complete, the positioning is performed by GPS

satellites so the location of your vehicle may not

be very accurate. This is not an error. When the

initial learning is complete, the location of your

vehicle can be detected with high accuracy.

❒ When an error message appears during the

initial learning, refer to “Message and how to

react to them” in the Operation Manual.

Selecting a Source with the AV

button

1 Turn the ignition switch (ACC) ON.

The navigation system’s power supply comes

on.

2 After the navigation system starts, press

the AV button to switch the screen.

The navigation map screen changes to the

audio source screen.

3 Press the AV button to turn the audio

source on.

4 Press the AV button to select a source.

Press the AV button repeatedly to switch

between the following sources:

[CD/ROM (MP3)/DISC] (built-in DVD drive)

— [MUSIC LIBRARY] (HDD player) — [FM]

(FM tuner) — [AM] (LW/MW tuner) — [iPod]

(iPod) — [M-CD] (multi-CD) — [TV] (televi-

sion) — [AV INPUT] (video input) — [AUX]

(Auxiliary equipment) — [EXT 1] (external

unit 1) — [EXT 2] (external unit 2)

❒ Press and hold the AV button to turn the

source off.

❒ In the following cases, the sound source can-

not be used:

— When a unit corresponding to each source

is not connected to the navigation system.

— When no disc is set in the navigation sys-

tem.

— When no magazine is set in the multi-CD

player.

— When [AUX Input] (auxiliary input) is

turned off (refer to Operation Manual).

— When [AV Input] (video input) is not set to

[Video] (refer to Operation Manual).

❒ “External unit” refers to a Pioneer product

(such as one available in the future) where,

although it is incompatible as a source, the

basic functions can be controlled by the navi-

gation system. Two external units can be con-

trolled by this product. When two external

units are connected, the product allocates

them to external unit 1 or external unit 2.

❒ When the [Auto ANT] mode is set to

[Radio], the vehicle’s antenna can be stowed

by following one of the steps below.

— Change the source from radio (AM or FM)

to another source.

— Turn the source off.

— Turn off the ignition switch (ACC OFF).

If the [Auto ANT] mode is set to [Power], the

vehicle’s antenna can be stowed only when

the ignition switch is turned off (ACC OFF).

➲ [Auto ANT] ➞ Operation Manual

Adjusting the Volume

•Use the VOL (/) button to adjust the

audio sound level.

Press the VOL (/) button to increase or

decrease the volume.

❒ To adjust the navigation volume, go to the

navigation menu.

➲ Navigation volume adjustment ➞ Opera-

tion Manual

Turning the Source Off

• Press the AV button and hold until the

source turns off.

❒ This navigation system also can be

switched off by turning the ACC (ignition)

OFF.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 24 25

Comments to this Manuals

No comments

Pioneer HD1 Manual Page 13

Comments to this Manuals

Related products and manuals for Car navigation systems Pioneer HD1