Pioneer VSX-1125-k User Manual download pdf (Page 61)

Using other functions

Setting the Video options

There are a number of additional picture settings you can

make using the VIDEO PARAMETER menu. The defaults,

if not stated, are listed in bold.

Important

• Note that if an option cannot be selected on the

VIDEO PARAMETER menu, it is unavailable due to

the current source, setting and status of the receiver.

• All of the setting items can be set for each input

function.

•Setting items other than V. CONV can only be

selected when V. CONV is set to ON.

1 Press , then press

VIDEO PARAMETER

2Use

/

to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check the

table below for notes on this.

3Use

/

to set as necessary.

See the table below for the options available for each

setting.

4Press

RETURN

to confirm and exit the menu.

k.• You can’t use the Virtual Front Height mode when the

headphones are connected to this receiver or when any of the

stereo, Front Stage Surround Advance, Sound Retriever Air or

Stream Direct modes is selected.

• The Virtual Front Height mode cannot be used when no surround

speaker is connected.

• When inputting Dolby True HD, DTS-HD or DTS Express audio

signals, the Virtual Front Height mode cannot be used if no

surround signals are recorded in the source.

Setting What it does Option(s)

V. CONV

(Digital Video

Conversion)

Converts video signals for output

from the MONITOR OUT jacks

(including HDMI OUT connector)

for all video types (see page 22).

OFF

RES

(Resolution)

Specifies the output resolution of

the video signal (when video input

signals are output at the HDMI

OUT connector, select this

according to the resolution of your

monitor and the images you wish

to watch).

AUTO

PURE

480p/576p

720p

1080i

1080p

1080/24p

ASP

(Aspect)

Specifies the aspect ratio when

input signals are output at the

HDMI output. Make your desired

settings while checking each

setting on your display (if the

image doesn’t match your monitor

type, cropping or black bands

appear).

THROUGH

NORMAL

RECEIVER

PCINEMA

d,e

(PureCinema)

This setting optimizes the

operation of the progressive

scanning circuit for playing film

materials. Normally set it to AUTO.

If the picture seems unnatural,

switch this to ON or OFF.

AUTO

OFF

P.MOTION

d,e

(Progressive

Motion)

Adjusts the motion and still picture

quality when video output is set to

progressive.

–4 to +4

Default: 0

YNR

Reduces noise in the luminance

(Y) signal.

0 to +8

Default: 0

CNR

Reduces noise in the input’s color

0 to +8

Default: 0

BNR

Reduces block noise (block-

shaped distortion generated upon

MPEG compression) in the

picture.

0 to +8

Default: 0

MNR

Reduces mosquito noise

(distortion generated at the

contours of the picture upon

MPEG compression) in the

picture.

0 to +8

Default: 0

DETAIL

Adjusts how sharp edges appear.0 to +8

Default: 0

BRIGHT

(Brightness)

Adjusts the overall brightness. –6 to +6

Default: 0

CONTRAST

Adjusts the contrast between light

and dark.

–6 to +6

Default: 0

HUE

Adjusts the red/green balance. –6 to +6

Default: 0

CHROMA

(Chroma

Level)

Adjusts saturation from dull to

bright.

–6 to +6

Default: 0

BLK SETUP

Corrects the black depth in the

brightness signal.

Normally select 7.5. If the dark

parts of the picture are all black

with this setting, select 0.

7.5

a.If the video picture deteriorates when this settings is switched ON,

switch it OFF.

b.• When set to a resolution with which the TV (monitor) is not

compatible, no picture is output. Also, in some cases no picture will

be output due to copyright protection signals. In this case, change

the setting.

• When AUTO is selected, the resolution is selected automatically

according to the capacity of the TV (monitor) connected by HDMI.

When PURE is selected, the signals are output with the same

resolution as when input (see About the video converter on page 22).

• If this is set to something other than AUTO, PURE and 480i/576i

analog signals are input, 480p/576p signals are output from the

component output terminals.

c.• If the image doesn’t match your monitor type, adjust the

aspect

ratio on the source component or on the monitor.

• This setting is only displayed when 480i/p or 576i/p video signals

are being input.

Setting What it does Option(s)

VSX-1325_UXJCB.book 61 ページ２０１０年３月９日　火曜日　午後３時４分

1 ... 60 61 62 ... 112

Comments to this Manuals

No comments

Pioneer VSX-1125-k User Manual Page 61

Comments to this Manuals

Related products and manuals for AV receivers Pioneer VSX-1125-k