Pioneer DDJ-S1 User Manual download pdf (Page 27)

English

! : Playback starts when is clicked, and stops when it is

clicked again.

: When is clicked, the track is played in sync with the

track on the deck whose [SYNC] button is pressed or the sample slot

whose this key is highlighted.

Setting the sample’s play start position

The position at which the tracks loaded in the sample slots start playing

can be set.

1 Click and select [Play form].

2 Click [c] or [d] and select one of the following:

! [start]: Sets the start position to the beginning of the track.

! [cue 1] – [cue 5]: Sets the start position to a hot cue.

! [loop 1] – [loop 9]: Sets the start position to a loop (loop in point).

Setting other items

1 Click .

2 From the pull-down menu, select the item to be

displayed or adjusted.

Using the mixer functions

Outputting sound

Set the volume of the power amplifiers connected to the [MASTER

OUT 1, MASTER OUT 2] terminals to an appropriate level. Note that

very loud sounds will be output if the volume is set too high.

1 Turn the [TRIM] control.

Adjusts the sound level input to the various decks.

2 Move the channel fader away from you.

Adjusts the sound level output from the various decks.

3 Move the crossfader.

Switch the deck whose sound is to be output from the speakers.

— This operation is not necessary when the crossfader curve selec-

tor switch is set to [THRU].

! Left edge: Only the sound of the channel assigned to the left of

the crossfader is output.

! Center position: The sound of the two decks is mixed and output.

! Right edge: Only the sound of the channel assigned to the right

of the crossfader is output.

! The deck assignments can be reversed from right to left and vice

versa with the [C.F. REV] button.

4 Turn the [MASTER LEVEL] control.

Audio signals are output from the [MASTER1] and [MASTER2]

terminals.

Equalization

Turn the [EQ (HI, MID, LOW) ] controls on the respective

decks.

These adjust the [HI] (high range), [MID] (middle range) and [LOW] (low

range), respectively.

Monitoring sound with headphones

The channel for monitoring over the headphones is called the [CUE]

channel. The sound of this channel is output from the headphones

regardless of the positions of the crossfader and channel fader.

! To monitor the sound of deck (A) or deck (B) over the headphones

without outputting it from the [MASTER] channel, use one of the

procedures below.

— Move the channel fader for the channel you do not want to output

from the [MASTER] channel to the nearest position towards you.

— Move the crossfader all the way to the side opposite the channel

you do not want to output.

! To monitor the sound of the microphone or external device (AUX)

without outputting it from the [MASTER] channel, select [Mute] on

the MIC/AUX monitor control panel.

= MIC/AUX monitor control panel (p.16)

1 Connect headphones to one of the [PHONES]

terminals.

2 Press the headphones [CUE] button for the channel

you want to monitor.

The headphones [CUE] button lights and the sound is output to the

headphones [CUE] channel.

! If you want to monitor the sound of both channels simultane-

ously, press both headphones [CUE] buttons simultaneously.

3 Click the [CUE] key for the microphone or external

device you want to monitor.

The [CUE] key is highlighted and the sound is output to the headphones

[CUE] channel.

! For details on the positions of keys, see Switching the jog dial

illumination on page 23.

4 Turn the [HEADPHONES MIXING] control.

Adjust the monitor volume balance between the sound of the [CUE]

channel and the sound of the [MASTER] channel.

! Turn counterclockwise: The relative volume of the [CUE] chan-

nel increases. When turned all the way counterclockwise, the

sound of the [MASTER] channel cannot be heard through the

headphones.

! Center position: The sound of the [CUE] channel and the sound

of the [MASTER] channel have the same volume.

! Turn clockwise: The relative volume of the [MASTER] channel

increases. When turned all the way clockwise, the sound of the

[CUE] channel cannot be heard through the headphones.

5 Turn the [HEADPHONES LEVEL] control.

The volume of the headphones is adjusted.

When multiple headphones [CUE] buttons are pressed, the sound of the

decks for which the buttons are pressed is mixed and output from the

headphones.

! When the headphones [CUE] button is pressed again, monitoring of

the deck’s sound is canceled.

! When the [CUE] key on the MIC/AUX monitor control panel is clicked

again, monitoring of the sound of the microphone or external device

is canceled.

Selecting the crossfader curve

characteristics

Switch the crossfader curve selector switch.

! [ ]: Makes a sharply increasing curve (if the crossfader is

moved away from the [A] side, audio signals are immediately

output from the [B] side).

! [ ]: Makes a gradually increasing curve (if the crossfader is

moved away from the [A] side, the sound on the [B] side gradu-

ally increases, while the sound on the [A] gradually decreases).

! [THRU]: Choose this when you do not want to use the crossfader.

1 ... 26 27 28 ... 112

Comments to this Manuals

No comments

Pioneer DDJ-S1 User Manual Page 27

Comments to this Manuals

Related products and manuals for DJ controllers Pioneer DDJ-S1