Pioneer VSX-924 User Manual download pdf (Page 100)

100

FAQ

Symptom Remedy

The volume level drops automati-

cally.

The temperature within the unit has exceeded the allowable value. Try moving the unit for

better ventilation (see Installing the receiver on page 9 ).

Volume seems different when input

is switched.

Set the Channel Level setting to ALL, then adjust the volume of the respective input

sources (see Input Volume Absorber on page 71 ).

When HDZONE is ON, multi-channel

audio sources are not output in the

main zone.

When HDZONE is selected in Speaker System and also the same HDMI input is selected

for both the main zone and HDZONE, 2-channel PCM audio sources are output from the

main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change

the HDZONE input.

BT AUDIO terminal

Symptom Remedy

The Bluetooth wireless technology

device cannot be connected or oper-

ated. Sound from the Bluetooth wire-

less technology device is not emitted

or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave

oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If

such an object is near the unit, set the unit far from it. Or, stop using the object emitting

the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too far from the unit and that

obstructions are not set between the Bluetooth wireless technology device and the unit.

Set the Bluetooth wireless technology device and the unit so that the distance between

them is less than about 10 m (33 ft.) and no obstructions exist between them.

The Bluetooth wireless technology device may not be set to the communication mode

supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless

technology device.

Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-

tooth wireless technology device. Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless technology device that sup-

ports A2DP profile and AVRCP profile.

Video

Symptom Remedy

No image is output when an input is

selected.

Check the video connections of the source component.

For HDMI, or when V.CONV is set to OFF and a TV and another component are con-

nected with different cords (in Setting the Video options on page 69 ), you must connect

your TV to this receiver using the same type of video cable as you used to connect your

video component. For the component video input, however, signals are only output from

the HDMI output, so when using the component video input, set V.CONV to ON.

Make sure the input assignment is correct for components connected using component

video or HDMI cables (see The Input Setup menu on page 39 ).

Check the video output settings of the source component.

Check that the video input you selected on your TV is correct.

Some components (such as video game units) have resolutions that may not be con-

verted. If adjusting this receiver’s Resolution setting (in Setting the Video options on

page 69 ) and/or the resolution settings on your component or display doesn’t work, try

switching V.CONV (in Setting the Video options on page 69 ) to OFF.

When the HDMI OUT 1/2 setting of the output parameter function is set to OFF, set it to

ON.

When the network function or iPod/USB input is selected in HDZONE, video connected

with the video cable or component cable is not output from the HDMI terminal. To output

video, turn off HDZONE or set HDZONE to some other input (page 72 ).

Noisy, intermittent, or distorted

picture.

Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

The picture’s movement is unnatu-

ral.

When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p, the picture

may not be displayed properly for some source materials. In this case, set the resolution

to something other than 1080/24p or 4K/24p (page 69 ).

Video parameters cannot be used. For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.

Use for video or input with a GUI display.

Cannot be used when the HDZONE is ON. Turn OFF the HDZONE.

1 2 ... 95 96 97 98 99 100 101 102 103 104 105 ... 122 123

Comments to this Manuals

No comments

Pioneer VSX-924 User Manual Page 100

Comments to this Manuals

Related products and manuals for AV receivers Pioneer VSX-924