Pioneer VSX-1125-k User Manual download pdf (Page 38)

Basic Setup

If you have a tripod, use it to place the microphone so that

it’s about ear level at your normal listening position. If you

do not have a tripod, use some other object to install the

microphone.

The Full Auto MCACC display appears once the

microphone is connected.

3 Select the parameters you want to set.

If the speakers are connected using any setup other than

Normal(SB/FH), be sure to set Speaker System before

the Auto MCACC Setup. See Speaker system setting on

page 83.

• Speaker System

– Shows the current settings.

When this is selected and ENTER is pressed, the

speaker system selection screen appears. Select the

proper speaker system, then press RETURN to return.

• EQ Type – This determines how the frequency

balance is adjusted.

• MCACC – The six MCACC presets are used for storing

surround sound settings for different listening

positions. Simply choose an unused preset for now

(you can rename it later in Data Management on

page 80).

• THX Speaker – Select YES if you are using THX

speakers (set all speakers to SMALL), otherwise leave

it set to NO.

4 Press and then select

START

5 Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re

using a subwoofer, make sure it is switched on and set to

a comfortable volume level.

6 Wait for the test tones to finish, then confirm the

speaker configuration in the GUI screen.

A progress report is displayed on-screen while the

receiver outputs test tones to determine the speakers

present in your setup. Try to be as quiet as possible while

it’s doing this.

If no operations are performed for 10 seconds while the

speaker configuration check screen is being displayed,

the Auto MCACC Setup will resume automatically. In this

case, you don’t need to select ‘OK’ and press ENTER in

step 7.

•With error messages (such as Too much ambient

noise! or Check microphone.), select RETRY after

checking for ambient noise (see Problems when

using the Auto MCACC Setup on pa

ge 39) and

verifying the mic connection. If there doesn’t seem to

be a problem, you can simply select GO NEXT and

continue.

The configuration shown on-screen should reflect the

actual speakers you have.

• If you see an ERR message (or the speaker

configuration displayed isn’t correct), there may be a

problem with the speaker connection.

If selecting RETRY doesn’t work, turn off the power

and check the speaker connections. If there doesn’t

seem to be a problem, you can simply use / to

select the speaker and / to change the setting

and continue.

Note

1 Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate measurement

impossible:

• Sofas or other soft surfaces.

• High places such as tabletops and sofa tops.

2 If you leave the GUI screen for over five minutes, the screen saver will appear.

3• When data measurement is taken, the reverb characteristics data (both before- and after-calibration) that this receiver had been storing will

be overwritten. If you want to save the reverb characteristics data before measuring, connect a USB memory device to this receiver and

transfer the data.

• When measure

ment is taken of the reverb characteristics data other than SYMMETRY, the data are not measured after the correction. If

you will need to measure after correcting data, take the measurement using the EQ Professional menu in the Manual MCACC setup (page 75).

4 If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Speaker system

setting on page 83 and make sure to connect your speakers as necessary before continuing to step 4.

Speaker System : Normal

(

SB/FH

)

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : SYMMETRY

MCACC : M1.MEMORY 1

THX Speaker : NO

RECEIVER

Now Analyzing... 2/9

Environment Check

1a.Full Auto MCACC

A/V RECEIVER

Exit Cancel

Ambient Noise : OK

Microphone :

Speaker YES/NO :

L : YES

FHL : YES

C : YES

FHR : YES

R : YES

SR : YES

SBR : YES

SBL : YES

SL : YES

SW : YES

1a.Full Auto MCACC

OK RETRY

A/V RECEIVER

Exit Cancel

VSX-1325_UXJCB.book 38 ページ２０１０年３月９日　火曜日　午後３時４分

1 ... 37 38 39 ... 112

Comments to this Manuals

No comments

Pioneer VSX-1125-k User Manual Page 38

Comments to this Manuals

Related products and manuals for AV receivers Pioneer VSX-1125-k