Pioneer Elite SC-35 User Manual Page 123
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Additional information
13
123
En
No sound
During loud playback the
power suddenly switches off.
• Turn down the volume.
• Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 106.
• Switch on the digital safety feature. While holding down ENTER on the front panel, press
STANDBY/ON to set this receiver to the standby mode. Use TUNE / to select D.SAFETY
OFF, and then use PRESET / to select 1 or 2 (select D.SAFETY OFF to deactivate this
feature). If the power switches off even with 2 switched on, turn down the volume. With 1 or 2 on,
some features may be unavailable.
The unit does not respond
when the buttons are pressed.
• Try switching the receiver off, then back on again.
• Try disconnecting the power cord, then connect again.
AMP ERR blinks in the display,
then the power automatically
switches off. The ADVANCED
MCACC blinks and the power
does not turn on.
• The receiver may have a serious problem. Do not try switching the receiver on. Unplug the receiver
from the wall and call a Pioneer authorized independent service company.
The PQLS flashes and power
turns off.
• There is a problem with the receiver’s power unit or fan. Try turning on the power after 1 minute. If
the same thing happens, the receiver is damaged. Unplug the receiver from the wall and call a
Pioneer authorized independent service company. (Other symptoms may appear when the power is
turned on.)
OVERHEAT blinks in the
display or AMP OVERHEAT
and the power indicator flash
and the power turns off.
• Allow the unit to cool down in a well-ventilated place before switching back on.
• Wait at least 1 minute, then try turning the power on again.
The receiver suddenly power
off or ADVANCED MCACC
flashes.
• The power unit is damaged. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
Display blinks 12V TRG ERR.• An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power back on.
Symptom Remedy
No sound is output when an
input function is selected.
No sound is output from the
front speakers.
• Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
• Make sure the correct input function is selected.
• Check that the MCACC setup microphone is disconnected.
• Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is
selected, you won’t be able to hear any other signal format.
• Check that the source component is connected properly (see Connecting your equipment on
page 20).
• Check that the speakers are connected properly (see Connecting the speakers on page 24).
No sound from the surround or
center speakers.
• Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected;
select one of the surround listening modes (see Listening in surround sound on page 59).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 115).
• Check the channel level settings (see Channel Level on page 116).
• Check the speaker connections (see Connecting the speakers on page 24).
No sound from surround back
speakers.
• Check that the surround back speakers are set to LARGE or SMALL, and the surround speakers
are not set to NO (see Speaker Setting on page 115).
• Check the speaker connections (see Connecting the speakers on page 24). If only one surround
back speaker is connected, make sure it’s connected to the left channel speaker terminal.
• Surround back speakers will not play while the Speaker System is set to Speaker B and audio is
being played through speaker B.
No sound from front height or
front wide speakers.
• Check that the front height or front wide speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 115).
• Check the speaker connections (see Connecting the speakers on page 24).
Symptom Remedy
SC-37_35_UXJCB.book 123 ページ ２０１０年３月９日 火曜日 午前９時３２分
- Operating Instructions 1
- IMPORTANT 2
- VENTILATION CAUTION 3
- K041_A1_En 4
- Contents 5
- (In case of SC-35) 7
- 11 The Advanced MCACC menu 7
- 13 Additional information 7
- Before you start 10
- Checking what’s in the box 10
- Installing the receiver 10
- Loading the batteries 10
- Controls and displays 12
- AV RECEIVER 13
- 1. Adv MCACC 13
- Front panel 18
- Connecting your equipment 20
- OUTPUT 5 V 21
- 150 mA MAX 21
- Placing the speakers 23
- Connecting the speakers 24
- Front height setup 27
- Front wide setup 27
- Speaker B setup 27
- Bi-Amping setup 27
- ZONE 2 setup 27
- About HDMI 28
- Connecting AM/FM antennas 36
- MULTI-ZONE setup 37
- LAN interface 38
- Bluetooth 39
- SETUP MIC 40
- Connecting an IR receiver 41
- Plugging in the receiver 42
- Basic Setup 43
- The Input Setup menu 45
- Basic playback 47
- Playing an iPod 48
- Playing a USB device 49
- Listening to the radio 52
- Listening to Satellite Radio 53
- Listening to XM Radio 53
- Listening to SIRIUS Radio 54
- Listening to your system 59
- Listening in stereo 61
- Full Band Phase Control 63
- Authorizing this receiver 64
- Server Name 65
- Listening to Rhapsody 66
- Checking about the Accounts 68
- About network playback 68
- Software update 69
- About playable file formats 70
- Glossary 71
- Control with HDMI function 72
- HDMI Setup 73
- Before using synchronization 73
- About synchronized operations 74
- Setting the PQLS function 75
- Using other functions 76
- Setting the Video options 78
- Using the MULTI-ZONE controls 79
- Web Control 81
- Main ZONE ZONE 3 81
- Resetting the system 82
- (In case of SC-37) 83
- AUTO/ALC/ 85
- PARAMETER 87
- FM UNBAL 75 AM LOOP 91
- Usable range 95
- Signal reflection 95
- For safe use 95
- Setting the backlight mode 99
- Using multi operations 100
- Using System off 100
- Controlling components 101
- The Advanced MCACC menu 104
- Manual MCACC setup 106
- Checking MCACC Data 110
- Data Management 112
- RECEIVER 114
- Speaker system setting 115
- Speaker Setting 115
- Channel Level 116
- Speaker Distance 116
- Network Setup menu 117
- IP address/Proxy setting 118
- Checking the MAC address 118
- Network Standby 118
- The Other Setup menu 119
- Flicker Reduction Setup 120
- RF Remote Setup 120
- EXTENSION Setup 120
- Multi Channel Input Setup 120
- Additional information 121
- Troubleshooting 122
- Surround sound formats 135
- About THX 135
- About iPod 137
- About SIRIUS and XM 137
- About FLAC 137
- Preset code list 139
- (SC-35 only) 139
- Specifications 143
- Cleaning the unit 144
- In the USA/Aux Etats-Unis 148
- In Canada/Aux Canada 148
Related products and manuals for TV Accessories Pioneer Elite SC-35
TV Accessories Pioneer VSX-1018AH-K User Manual
(100 pages)
(100 pages)
TV Accessories Pioneer VSX-D914 User Manual
(71 pages)
(71 pages)
TV Accessories Pioneer SC-07 User Manual
(38 pages)
(38 pages)
TV Accessories Pioneer VSX-D811S User Manual
(76 pages)
(76 pages)
(78 pages)
(80 pages)
(96 pages)
(96 pages)
(78 pages)© 2020, manymanuals.com. All rights reserved. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals