Pioneer GM-X952 User Manual download pdf (Page 6)

Connecting the Unit

CAUTION

• Disconnect the negative (-) terminal of the bat

tery to avoid the risk of short-circuit and damage

to the unit.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

• Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

Make sure that wires will not interfere with mov

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

Do not shorten any wires. Otherwise the protec

tion circuit may fail to work when it should.

Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

To prevent damage

• Do not ground the speaker wire directly or con

nect a negative (-) lead wire for several speakers.

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre

ational vehicle, truck or bus, check the battery

voltage.

• If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

• If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on— regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

Speakers to be connected to the amplifier should

conform with the standards listed below. If they

do not conform, they may catch fire, emit smoke

or become damaged. The speaker impedance

must be 2 to 8 ohms for stereo connection, and

4 to 8 ohms for monaural and other bridge con

nection.

Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

Cords for ihis produel and those lor other prod

ucts may be different colors even if they have the

same function. When eonneetiiig this product to

another product, refer to the supplied Installation

manuals of both products and eonneel cords that

have the same function.

Speaker Channel Speaker Type

Power

Two-channel

Subwoofer

Nominal input: Min. 125 W

Other than subwoofer

Max. input: Min. 200 W

One-channel

Subwoofer

Nominal input: Min. 380 W

Other than subwoofer

Max. input: Min. 600 W

3. Verbind de luidsprekerdraden met

de luidsprekeraansluiting.

• Haal de draden door de aansluitingafdekking

en verbind de luidsprekerdraden.

• Zet de luidsprekerdraden goed met de

schroeven van de aansluiting vast.

Aansluitpuntschroef

4. Druk op de aansluitingafdekking.

Aansluiten van de luidspreker

draden

________________________

De uitgangsfunctie voor de luidspreker

kan voor twee kanalen (stereo) of een

kanaal (mono) worden ingesteld. Sluit de

luidsprekersnoercn aan overeenkomstig de

gewenste functie zoals aangegeven in de

onderstaande afbeeldingen.

Twee kanalen functie (stereo)

(Rechts)

Luidspreker

(Links)

Een kanaal functie (mono)

1 2 3 4 5 6 7 ... 32

Comments to this Manuals

No comments

Pioneer GM-X952 User Manual Page 6

Comments to this Manuals

Related products and manuals for Car Multimedia Pioneer GM-X952