Pioneer PRS-D200 User Manual download pdf (Page 5)

ENGLISH

Connection Diagram

• This diagram shows connections using external output (subwoofer output). Slide the input

switch to the left.

• When you connect with speaker output, connections defers from the diagram. For details,

see the “Using the Speaker Input” section. In either case, you need to set the input switch.

For details, see the “Setting the Unit” section.

Grommet

Special red battery wire [RD-223] (sold separately)

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to the

positive (+) terminal of the battery.

Ground wire (black) [RD-223] (sold separately)

Connect to metal body or chassis.

Speaker output terminal

See the “Connecting the Speaker

Wires” section for speaker

connection instructions.

RCA input jack

Connecting wire with RCA pin

plugs (sold separately).

Car stereo with

RCA output jacks

Fuse (30 A)

External Output

Fuse (30 A)

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car stereo

(SYSTEM REMOTE CONTROL). The female terminal can be connected to the auto-antenna relay

control terminal. If the car stereo does not have a system remote control terminal, connect the male

terminal to the power terminal through the ignition switch.

Fuse (30 A)

RCA output jack

Bass Boost

Remote Control

Bass Boost Remote

Control Wire

Jack for the bass boost remote control

Connect this jack and the bass boost

remote control with the bass boost

remote control wire.

6 m

Amplifier with RCA

input jacks

RCA input

Connecting the Unit

! CAUTION

• Disconnect the negative (–) terminal of the battery to avoid the risk of short-circuit and

damage to the unit.

• Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive

tape around it where they lie against metal parts.

• Do not route wires where they will get hot, for example where the heater will blow over them.

If the insulation heats up, it may become damaged, resulting in a short-circuit through the

vehicle body.

• Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

• Do not shorten any wires. Otherwise the protection circuit may fail to work when it should.

• Never feed power to other equipment by cutting the insulation of the power supply wire to

tap from the wire. The current capacity of the wire will be exceeded, causing overheating.

• Never replace the fuse with one of greater value or rating than the original fuse. Use of an

improper fuse could result in overheating and smoke and could cause damage to the

product and injury including burns.

! CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or connect a negative (–) lead wire for several

speakers.

• This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in

a recreational vehicle, truck or bus, check the battery voltage.

• If the car stereo is kept on for a long time while the engine is at rest or idling, the battery may

go dead. Turn the car stereo off when the engine is at rest or idling.

• If the system remote control wire of the amplifier is connected to the power terminal through

the ignition switch (12 V DC), the amplifier will always be on when the ignition is on –

regardless of whether the car stereo is on or off. Because of this, the battery could go dead

if the engine is at rest or idling.

• Speakers to be connected to the amplifier should conform with the standards listed below.

If they do not conform, they may catch fire, emit smoke or become damaged. The speaker

impedance must be 2 to 8 ohms for stereo connection, and 4 to 8 ohms for monaural and

other bridge connection.

• Install and route the separately sold battery wire as far away as possible from the speaker

wires. Install and route the separately sold battery wire, ground wire, speaker wires and the

amplifier as far away as possible from the antenna, antenna cable and tuner.

• Cords for this product and those for other products may be different colors even if they have

the same function. When connecting this product to another product, refer to the supplied

Installation manuals of both products and connect cords that have the same function.

Speaker Channel Speaker Type Power

Two-channel

Subwoofer Nominal input: Min. 150 W

Other than subwoofer Max. input: Min. 300 W

One-channel

Subwoofer Nominal input: Min. 600 W

Other than subwoofer Max. input: Min. 1200 W

MAN-PRS-D200-GB.fm Page 5 Monday, February 20, 2006 4:17 PM

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Pioneer PRS-D200 User Manual Page 5

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Pioneer PRS-D200