Pioneer SC-LX73 User Manual Page 122
- Page / 146
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Additional information
13
122
En
Video
Settings
Symptom Remedy
No image is output when an
input is selected.
• Check the video connections of the source component (see page 31).
• For HDMI, or when digital video conversion is set to OFF and a TV and another component are
connected with different cords (in Setting the Video options on page 74), you must connect your TV
to this receiver using the same type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component video or
HDMI cables (see The Input Setup menu on page 44).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If
adjusting this receiver’s Resolution setting (in Setting the Video options on page 74) and/or the
resolution settings on your component or display doesn’t work, try switching Digital Video
Conversion (in Setting the Video options on page 74) to OFF.
Can’t record video. • Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video
cable is used for connecting both the recorder and the video source (the one you want to record) to
this receiver.
Noisy, intermittent, or distorted
picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the
video quality may just be poor (with some video game units, for example). The picture quality may
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect
the source and display device using the same type of connection (component or composite), then
start playback again.
Video signals are not output
from the component terminal.
• When a monitor only compatible with resolutions of 480i is connected to the component terminal
and another monitor is connected to the HDMI terminal, the video signals may not be output to the
monitor connected to the component terminal. If this happens, do the following:
– Turn off the power of the monitor connected to the HDMI terminal.
– Change the VIDEO PARAMETER menu RES setting.
– Video signals from the HDMI terminal cannot be output to the component terminals. Input the
video signals from the player or other source to the composite or component terminals. When using
the component terminal, assign it at Input Setup.
Symptom Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see
also Problems when using the Auto MCACC Setup on page 44). If the noise level cannot be kept low
enough, you will have to set up the surround sound manually (page 110).
• When using only one surround back speaker, connect it to the SURROUND BACK L (Single)
terminals.
• To use a 5.1-channel speaker set, use the surround speakers for the surround channel, not the
surround back channel.
• Make sure there are no obstacles between the speakers and the microphone.
• If Reverse Phase is displayed, try the following:
– The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.
–
Depending on the type of speakers and their installation conditions,
Reverse Phase
may be
displayed even if the speakers are properly connected. If this happens, select
GO NEXT
and continue.
– If the speaker is not pointed to the microphone (listening position) or when using speakers that
affect the phase (dipole speakers, reflective speakers, etc.), it may not be possible to properly identify
the polarity.
After using the Auto MCACC
Setup, the speaker size setting
is incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.
Switch off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (bass reproduction capabilities of the speakers, room size,
speaker placement, etc.) this may occur in some cases. Change the speaker setting manually in
Speaker Setting on page 111, and use the ALL (Keep SP System) option for the Auto MCACC menu
in Automatic MCACC (Expert) on page 100 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 103)
properly.
• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are
matched up properly).
- Operating Instructions 1
- IMPORTANT 2
- VENTILATION CAUTION 3
- Contents 4
- (In case of SC-LX73) 6
- 11 The Advanced MCACC menu 6
- 13 Additional information 6
- Checking what’s in the box 9
- Installing the receiver 9
- Loading the batteries 9
- Before you start 10
- Controls and displays 11
- AV RECEIVER 12
- 1. Adv MCACC 12
- STANDBY/ON 17
- Connecting your equipment 19
- Connecting the RF adapter 20
- Placing the speakers 22
- Connecting the speakers 23
- Front height setup 26
- Front wide setup 26
- Speaker B setup 26
- Bi-Amping setup 26
- ZONE 2 setup 26
- About HDMI 27
- Connecting AM/FM antennas 35
- MULTI-ZONE setup 36
- LAN interface 37
- Bluetooth 38
- Connecting a USB device 39
- MCACC output 39
- Connecting an IR receiver 40
- Plugging in the receiver 41
- Basic Setup 42
- The Input Setup menu 44
- Basic playback 46
- Playing an iPod 47
- Playing a USB device 48
- Listening to the radio 51
- Listening to your system 56
- Listening in stereo 58
- Full Band Phase Control 60
- Server Name 62
- About list of Internet radio 63
- About network playback 64
- Software update 65
- About playable file formats 66
- Glossary 67
- Control with HDMI function 68
- HDMI Setup 69
- Before using synchronization 69
- About synchronized operations 70
- Setting the PQLS function 71
- Using other functions 72
- Setting the Video options 74
- Using the MULTI-ZONE controls 75
- Web Control 77
- Main ZONE ZONE 3 77
- Resetting the system 78
- (In case of SC-LX83) 79
- AUTO/ALC/ 81
- Direct function 83
- Controlling components 84
- FM UNBAL 75 AM LOOP 87
- OUTPUT 5 V 87
- 150 mA MAX 87
- Usable range 91
- Signal reflection 91
- For safe use 91
- Setting the backlight mode 95
- Using multi operations 96
- Using System off 96
- The Advanced MCACC menu 100
- Manual MCACC setup 102
- Checking MCACC Data 106
- Data Management 108
- RECEIVER 110
- Speaker Setting 111
- Speaker system setting 111
- Channel Level 112
- Speaker Distance 112
- Network Setup menu 113
- IP address/Proxy setting 114
- Checking the MAC address 114
- Network Standby 114
- The Other Setup menu 115
- Flicker Reduction Setup 116
- RF Remote Setup 116
- EXTENSION Setup 116
- Multi Channel Input Setup 116
- Additional information 117
- Troubleshooting 118
- Surround sound formats 130
- About THX 130
- About iPod 132
- About FLAC 132
- Preset code list 134
- (SC-LX73 only) 134
- Specifications 141
- Cleaning the unit 142
- Radio wave caution 142
- PIONEER CORPORATION 146
Related products and manuals for Home Theater Systems Pioneer SC-LX73
Home Theater Systems Pioneer DCS-590 User Manual
(126 pages)
(126 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 3.914 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals