Pioneer SC-LX73 User Manual Page 80
- Page / 146
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Controlling the rest of your system (In case of SC-LX83)
10
80
En
Operating multiple receivers
The remote control included with this receiver can be
used to operate up to three other receivers (of the same
model as this receiver) in addition to this receiver.
1
The
receiver to be operated is switched by inputting the
preset code to set the remote control setting.
• Set the remote modes on the receivers before using
this function (see Remote Control Mode Setup on
page 115).
1 Check that the remote control’s
MULTI-ZONE
selector switch is set to
MAIN
and that the operation
selector switch is set to
RECEIVER
.
2 While pressing
MULTI OPERATION
, press
HOME
MENU
.
The remote display shows SETUP MENU.
3Use
/
to select ‘
CHANGE RC MODE
’, then press
ENTER
.
4Use
/
to select the remote mode.
RC MODE 1 to 4 can be selected.
5 Press ENTER to set the remote mode.
The selected mode flashes for 3 seconds.
To operate another receiver, start over from step 1 to
input its preset code.
Setting the remote to control other
components
Most components can be assigned to one of the input
function buttons (such as
DVD
or
CD
) using the component’s
manufacturer preset code stored in the remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
If you can’t find a preset code that matches the
component you want to control, you can still teach the
remote individual commands from another remote
control (see Programming signals from other remote
controls on page 81).
• For greater convenience, assign the TV connected to
the MONITOR OUT terminal to the
TV
operation
selector switch, and assign your satellite/cable receiver
or set-top box connected to the TV input terminal to the
TV
input button. If a single device is connected to both
terminals, that device should be assigned to both the
TV
operation selector switch and
TV
input buttons.
• Devices may be assigned to the following input
function buttons.
Selecting preset codes directly
1 While pressing
MULTI OPERATION
, press
HOME
MENU
.
The remote display shows SETUP MENU.
2Use
/
to select ‘PRESET RECALL’, then press
ENTER.
3 Press the input function button for the component
you want to control, then press
ENTER
.
When assigning preset codes to TV CONTROL, set the
remote control operation selector switch to TV here.
The remote display shows the component you want to
control (for example DVD or TV).
2
4Use
/
to select the first letter of the brand name
of your component, then press
ENTER
.
This should be the manufacturer’s name (for example, P
for Pioneer).
5Use
/
to select the manufacturer’s name from
the list, then press
ENTER
.
6Use
/
to select the proper code from the list,
then try using this remote with your component.
The code should start with the component type (for
example, DVD 020). If there is more than one, start with
the first one.
3
To try out the remote control, switch the component on or
off (into standby) by pressing
SOURCE
. If it doesn’t seem
to work, select the next code from the list (if there is one).
• If you can’t find or properly enter a preset code, you
can still teach the remote individual commands from
another remote control (see Programming signals
from other remote controls on page 81).
7 If your component is controlled successfully, press
ENTER
to confirm.
The remote display shows OK.
Note
1 This function is only valid when RECEIVER is set to IR MODE at the remote control’s IR/RF SELECT setting (page 88).
2 You can’t assign TUNER, HMG NET RADIO, ADAPTER and iPod USB.
3 • When using a Pioneer HDD recorder, please select PIONEER DVR 450, 451 or 452.
• When using a Pioneer flat panel TV released prior to summer 2005, please select preset code 644.
RECEIVER SOURCE
MAIN
MULTI
OPERATION
ZONE2 3
INPUT SELECT
PHONO
VIDEO
CD-R
IN
AUX
DVD
iPod
USB
OPTION
MULTI CH
ADAPTER
NET RADIO
CD
TUNER
HMG
BD
TV
HDMIDVR
BDR
12
MULTI
OPERATION
- Operating Instructions 1
- IMPORTANT 2
- VENTILATION CAUTION 3
- Contents 4
- (In case of SC-LX73) 6
- 11 The Advanced MCACC menu 6
- 13 Additional information 6
- Checking what’s in the box 9
- Installing the receiver 9
- Loading the batteries 9
- Before you start 10
- Controls and displays 11
- AV RECEIVER 12
- 1. Adv MCACC 12
- STANDBY/ON 17
- Connecting your equipment 19
- Connecting the RF adapter 20
- Placing the speakers 22
- Connecting the speakers 23
- Front height setup 26
- Front wide setup 26
- Speaker B setup 26
- Bi-Amping setup 26
- ZONE 2 setup 26
- About HDMI 27
- Connecting AM/FM antennas 35
- MULTI-ZONE setup 36
- LAN interface 37
- Bluetooth 38
- Connecting a USB device 39
- MCACC output 39
- Connecting an IR receiver 40
- Plugging in the receiver 41
- Basic Setup 42
- The Input Setup menu 44
- Basic playback 46
- Playing an iPod 47
- Playing a USB device 48
- Listening to the radio 51
- Listening to your system 56
- Listening in stereo 58
- Full Band Phase Control 60
- Server Name 62
- About list of Internet radio 63
- About network playback 64
- Software update 65
- About playable file formats 66
- Glossary 67
- Control with HDMI function 68
- HDMI Setup 69
- Before using synchronization 69
- About synchronized operations 70
- Setting the PQLS function 71
- Using other functions 72
- Setting the Video options 74
- Using the MULTI-ZONE controls 75
- Web Control 77
- Main ZONE ZONE 3 77
- Resetting the system 78
- (In case of SC-LX83) 79
- AUTO/ALC/ 81
- Direct function 83
- Controlling components 84
- FM UNBAL 75 AM LOOP 87
- OUTPUT 5 V 87
- 150 mA MAX 87
- Usable range 91
- Signal reflection 91
- For safe use 91
- Setting the backlight mode 95
- Using multi operations 96
- Using System off 96
- The Advanced MCACC menu 100
- Manual MCACC setup 102
- Checking MCACC Data 106
- Data Management 108
- RECEIVER 110
- Speaker Setting 111
- Speaker system setting 111
- Channel Level 112
- Speaker Distance 112
- Network Setup menu 113
- IP address/Proxy setting 114
- Checking the MAC address 114
- Network Standby 114
- The Other Setup menu 115
- Flicker Reduction Setup 116
- RF Remote Setup 116
- EXTENSION Setup 116
- Multi Channel Input Setup 116
- Additional information 117
- Troubleshooting 118
- Surround sound formats 130
- About THX 130
- About iPod 132
- About FLAC 132
- Preset code list 134
- (SC-LX73 only) 134
- Specifications 141
- Cleaning the unit 142
- Radio wave caution 142
- PIONEER CORPORATION 146
Related products and manuals for Home Theater Systems Pioneer SC-LX73
Home Theater Systems Pioneer DCS-590 User Manual
(126 pages)
(126 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 1.448 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals