Pioneer SC-LX73 User Manual Page 123
- Page / 146
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Additional information
13
123
En
Professional Calibration EQ graphical output
Display
SC-LX83 only: Gauge (value)
does not increase with the
Precision Distance
adjustment.
• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are
matched up properly).
• Perform the Full Auto MCACC procedure before the Precision Distance adjustment (see
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 42).
• Place the microphone accurately in the same position as when the Full Auto MCACC procedure
was performed.
• Do not move the speaker used as the reference point. Also, adjust in order, starting from the front
right speaker.
• When adjusting the speaker positions, do not move the speakers much; only move them about 2
cm towards or away from the microphone.
• If you forget exactly where the microphone should be positioned or if there are problems after the
procedure has been performed repeatedly, re-calibrate the distance using the Full Auto MCACC
procedure, then without moving the microphone redo the Precision Distance adjustment.
The display shows
KEY LOCK ON
when you try to make settings.
• With the receiver in standby, press STANDBY/ON for about 10 seconds while holding down
SPEAKERS to disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
• Settings are only stored if all the zones are turned off. Turn off all the zones before unplugging the
power cord.
The various system settings are
not stored.
• Make sure the blue STANDBY/ON light has gone out before unplugging.
Symptom Remedy
The EQ response displayed in
the graphical output following
calibration does not appear
entirely flat.
• There are cases where the graph does not appear flat (even when selecting ALL CH ADJ in the Auto
MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal
sound.
• Areas of the graph may appear identical (before and after) when there is little or no adjustment
needed.
• The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using
the Manual MCACC setup on
page 102 do not appear to
change the graphical output.
• Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the graphical output. However, these adjustments are taken into account by the
filters dedicated to overall system calibration.
Lower frequency response
curves do not seem to have
been calibrated for SMALL
speakers.
• Low frequencies used in bass management (the subwoofer channel) will not change for speakers
that have been specified as SMALL in the configuration, or do not output these frequencies.
• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable
sound is output for display.
Symptom Remedy
The display is dark or off. • Press DIMMER repeatedly to select a different brightness.
You can’t get DIGITAL to
display when using SIGNAL
SEL.
• Check the digital connections and make sure that the digital inputs are assigned correctly (see The
Input Setup menu on page 44).
• If the multichannel analog inputs are selected, select a different input function.
2 DIGITAL or DTS does not
light when playing Dolby/DTS
software.
• These indicators do not light if playback is paused.
• Check the playback (especially the digital output) settings of the source component.
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light.
• Check that the player is connected using a digital connection.
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 59).
• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.
When playing certain discs,
none of the receiver’s format
indicators light.
• The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what
audio tracks are recorded on the disc.
Symptom Remedy
- Operating Instructions 1
- IMPORTANT 2
- VENTILATION CAUTION 3
- Contents 4
- (In case of SC-LX73) 6
- 11 The Advanced MCACC menu 6
- 13 Additional information 6
- Checking what’s in the box 9
- Installing the receiver 9
- Loading the batteries 9
- Before you start 10
- Controls and displays 11
- AV RECEIVER 12
- 1. Adv MCACC 12
- STANDBY/ON 17
- Connecting your equipment 19
- Connecting the RF adapter 20
- Placing the speakers 22
- Connecting the speakers 23
- Front height setup 26
- Front wide setup 26
- Speaker B setup 26
- Bi-Amping setup 26
- ZONE 2 setup 26
- About HDMI 27
- Connecting AM/FM antennas 35
- MULTI-ZONE setup 36
- LAN interface 37
- Bluetooth 38
- Connecting a USB device 39
- MCACC output 39
- Connecting an IR receiver 40
- Plugging in the receiver 41
- Basic Setup 42
- The Input Setup menu 44
- Basic playback 46
- Playing an iPod 47
- Playing a USB device 48
- Listening to the radio 51
- Listening to your system 56
- Listening in stereo 58
- Full Band Phase Control 60
- Server Name 62
- About list of Internet radio 63
- About network playback 64
- Software update 65
- About playable file formats 66
- Glossary 67
- Control with HDMI function 68
- HDMI Setup 69
- Before using synchronization 69
- About synchronized operations 70
- Setting the PQLS function 71
- Using other functions 72
- Setting the Video options 74
- Using the MULTI-ZONE controls 75
- Web Control 77
- Main ZONE ZONE 3 77
- Resetting the system 78
- (In case of SC-LX83) 79
- AUTO/ALC/ 81
- Direct function 83
- Controlling components 84
- FM UNBAL 75 AM LOOP 87
- OUTPUT 5 V 87
- 150 mA MAX 87
- Usable range 91
- Signal reflection 91
- For safe use 91
- Setting the backlight mode 95
- Using multi operations 96
- Using System off 96
- The Advanced MCACC menu 100
- Manual MCACC setup 102
- Checking MCACC Data 106
- Data Management 108
- RECEIVER 110
- Speaker Setting 111
- Speaker system setting 111
- Channel Level 112
- Speaker Distance 112
- Network Setup menu 113
- IP address/Proxy setting 114
- Checking the MAC address 114
- Network Standby 114
- The Other Setup menu 115
- Flicker Reduction Setup 116
- RF Remote Setup 116
- EXTENSION Setup 116
- Multi Channel Input Setup 116
- Additional information 117
- Troubleshooting 118
- Surround sound formats 130
- About THX 130
- About iPod 132
- About FLAC 132
- Preset code list 134
- (SC-LX73 only) 134
- Specifications 141
- Cleaning the unit 142
- Radio wave caution 142
- PIONEER CORPORATION 146
Related products and manuals for Home Theater Systems Pioneer SC-LX73
Home Theater Systems Pioneer DCS-590 User Manual
(126 pages)
(126 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 0.247 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals